e-design public:solutions:gateway:biddle_tls_modbus_rtu:doc

public:solutions:gateway:biddle_tls_modbus_rtu:doc:bems

Anonymous (anonymous@undisclosed.example.com) — 2013-08-30T13:32:12+00:00

BEMS/TESTFILT This command will give variable „FilterPct“ as response. This is the filter dirty percentage. With command „testfilt 1“ you will start the filter test run. This works the same as „menu 2 1“.

public:solutions:gateway:biddle_tls_modbus_rtu:doc:bems_bems

Anonymous (anonymous@undisclosed.example.com) — 2013-09-11T14:55:25+00:00

BEMS parameter BEMS/TempUitbl Average discharge temperature units BEMS/TBuiten actual outside temperature. BEMS/TbFilt used outside temperature in control This is time based filtered temperature of TBuiten BEMS/TestMode

public:solutions:gateway:biddle_tls_modbus_rtu:doc:bems_errflags

Anonymous (anonymous@undisclosed.example.com) — 2015-04-08T13:31:13+00:00

Values for BEMS/ErrFlags bit / Error number code Errflags2 description 0 E6 Outlet temperature sensor below 5 °C 1 E2 Communication error or invalid configuration

public:solutions:gateway:biddle_tls_modbus_rtu:doc:bems_setbems

Anonymous (anonymous@undisclosed.example.com) — 2013-09-11T14:46:31+00:00

SETBEMS parameter SETBEMS/heat heat on/off 0n=1 SETBEMS/auto fan speed control Auto(chips)=1 or Manual=0 must be 1 SETBEMS/fan fan speed setting in Manual mode SETBEMS/fanoffs Fan speed correction in Auto mode.

public:solutions:gateway:biddle_tls_modbus_rtu:doc:bems_testfilt

Anonymous (anonymous@undisclosed.example.com) — 2013-09-11T14:59:38+00:00

BEMS/TESTFILT parameter TESTFILT/FilterPct filter dirt percentage based on fan speed test at speed 6. Over 100% - a filter dirt error signal and filter dirt output will be activated. This will be reset, when filter dirt percentage drops below 50%. (it can not have negative value)

public:solutions:gateway:biddle_tls_modbus_rtu:doc:conf_flws

Anonymous (anonymous@undisclosed.example.com) — 2013-04-24T06:45:14+00:00

CONF/flws VER<3.1 always 0 VER >=3.1 1 old flow sensor 2 pressure sensor (new) 3 no sensor

public:solutions:gateway:biddle_tls_modbus_rtu:doc:ctrl

Anonymous (anonymous@undisclosed.example.com) — 2013-09-11T19:08:56+00:00

CTRL parameter CTRL/1/tuitsp setpoint for discharge temperature (0,1 degree) CTRL/1/klpsp setpoint runtime motor for positioning discharge grill (time ) CTRL/1/flwsp setpoint for fan speed (0-6)

public:solutions:gateway:biddle_tls_modbus_rtu:doc:ctrl_flwspeed

Anonymous (anonymous@undisclosed.example.com) — 2013-02-26T15:47:00+00:00

Values of CTRL/FlwSpeed The value is given in (m)Volts The following values can appear: * 0 ( no sensor connected) * 0,5V (sensor connected ; fan off ; no pressure difference) * >0,6V and less then 4,5V -a fan active and sensor working.

public:solutions:gateway:biddle_tls_modbus_rtu:doc:menu

Anonymous (anonymous@undisclosed.example.com) — 2015-02-24T12:47:25+00:00

Biddle/TLS MENU Parameter parameter # description range read write remark 1 discharge temperature control 0 - 5 0 - AU (30-40 based on fanspeed) 1 - 30 2 - 35 3 - 40 4 - HI (high temperature) 5 - PI (PI control) R/W

public:solutions:gateway:biddle_tls_modbus_rtu:doc:modbus

Anonymous (anonymous@undisclosed.example.com) — 2015-04-27T07:51:25+00:00

Biddle-TLS / ModBus-RTU ModBus accesss Some registers have the type float. It's important to know that these are always 4 byte which means 2 modbus words - so the length has to be 2. It's possible to read registers of the same space blockwisen but in this case it's important to care about the endianness. For example it's possible to read all CTRL or LUGO registers at once.

public:solutions:gateway:biddle_tls_modbus_rtu:doc:model

Anonymous (anonymous@undisclosed.example.com) — 2013-09-11T19:14:13+00:00

MODEL parameter MODEL/sterkte desired fan speed MODEL/tuitbl discharge set point (0,1 degree) MODEL/tbuiten actual outside temperature detected by control (0,1 degree)

public:solutions:gateway:biddle_tls_modbus_rtu:doc:mounting

Anonymous (anonymous@undisclosed.example.com) — 2012-01-06T09:22:00+00:00

Einbau Teileliste * Fernbedienung inkl. 2-PIN Stecker für OnOff * ModBus-Interface mit Kabel (Flachbandkabel + ModBus + OnOff) * 3x Unterlegscheibe M3 * 1x Schraube M3x10 1. Kabelhalter entfernen Entfernen Sie die Kabelhalter auf der Rückseite der Fernbedienung,

public:solutions:gateway:biddle_tls_modbus_rtu:doc:remote_type

Anonymous (anonymous@undisclosed.example.com) — 2014-02-27T12:34:52+00:00

remote type Shows if there is: * the old grey remote attached * the newer BEMS module attached * FCC unit attached This depends on the VER command and tries to guess the current device type by it's response.

public:solutions:gateway:biddle_tls_modbus_rtu:doc:svn_log

Anonymous (anonymous@undisclosed.example.com) — 2013-04-23T12:47:11+00:00

Subversion / Log ------------------------------------------------------------------------ r207 | erazor | 2013-04-23 13:41:01 +0200 (Tue, 23 Apr 2013) | 2 lines timing changed ------------------------------------------------------------------------ r206 | erazor | 2013-04-23 11:37:21 +0200 (Tue, 23 Apr 2013) | 2 lines bugfix for version 2/CONF/AC_Count ------------------------------------------------------------------------ r205 | erazor | 2013-04-23 11:03:24 +0200 (Tue, 23 Apr 2013) | 2 li…